Clever SLC 1100
Solvent-Free, 1-Component, Waterproof, Elastomeric, Moisture-Curing Silicone Coating
Clever SLC 1100 is a single-component, 100% silicone-based, solvent-free, UV-resistant, highly flexible, moisture-curing waterproofing material with high adhesion properties.
• Easy to apply and use in enclosed areas.
• Low VOC content.
• Excellent adhesion to many substrates without a primer.
• Easy to clean.
• Excellent UV and alkali resistance.

FEATURES AND BENEFITS
-
• Easy to apply and use in enclosed areas.
• Low VOC content.
• Excellent adhesion to many substrates without a primer.
• Easy to clean.
• Excellent UV and alkali resistance.
FIELDS OF APPLICATION
-
• On metal roofs,
• On metal-clad areas,
• On timber cladding,
• Over bituminous membranes,
• Concrete roofs,
• Mineral-surfaced roofs,
• In the renovation of old polyurethane foam roofs.
Product Details
• Metal substrates: 0.60–0.70 kg/m²
• Smooth substrates: 0.60–0.70 kg/m²
• Rough substrates: 0.90–1.00 kg/m²
White, in 5 kg and 20 kg plastic pails.
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
| PROPERTY | TEST METHOD | VALUE |
|---|---|---|
| Chemical Base | Clever Lab. | Silicone |
| Solids Content | ASTM D1644 | 96% |
| Flash Point | ASTM D3278 | ≥81 °C |
| Tensile Strength at Break (23 °C) | ASTM D2370 | 2.00 N/mm² |
| Tensile Strength at Break (−18 °C) | ASTM D2370 | 2.00 N/mm² |
| Application Temperature | Clever Lab. | +10 °C to +40 °C |
| Elongation at Break (23 °C) | ASTM D2370 | 200% |
| Elongation at Break (−18 °C) | ASTM D2370 | 200% |
| VOC content | EPA 24 | ≤50 g/L |
| Wet Adhesion – Polyurethane Foam | ASTM D903 | Pass |
| Wet Adhesion – Acrylic Coating | ASTM D903 | Pass |
| Wet Adhesion – Galvanised Metal | ASTM D903 | Pass |
| Wet Adhesion – EPDM | ASTM D903 | Pass |
| Wet Adhesion – PVC | ASTM D903 | Pass |
| Water Vapour Permeability | ASTM E96 | Pass |
| Solar Reflectance | ASTM C1549 | Pass |
| Thermal Emittance | ASTM C1371 | Pass |
| Initial Drying Time | Clever Lab. | 24 h |
| Waiting Time between Coats | Clever Lab. | 24–48 h |
Application
• SURFACE PREPARATION
Before application, all contaminants that impair bonding and adhesion, such as oil, grease, paraffin residues, cement laitance, loose particles, release agents and old cured membranes, must be removed from the substrate. After washing with high-pressure water, the substrate must be dried thoroughly. Surface defects must be repaired with suitable products.
• APPLICATION
Before use, open the container and mix for 2–3 minutes with a low-speed mixer. Apply by roller, brush or spray until the entire surface is covered, so as to form a uniform, continuous film.
• Not recommended for unsound substrates.
• Do not use specially coloured Clever SLC 1100 on asphalt surfaces.
• Colour change may occur on asphalt surfaces.