ClvFloor 330 TEX
Two-Component, Roller-Applied, Textured, Solvent-Free Epoxy Top Coat
ClvFloor 330 TEX is a two-component, epoxy-resin-based, textured, solvent-free, coloured coating material with an orange-peel finish.
• Good chemical and mechanical resistance.
• Used as a decorative top coat with an orange-peel texture.
• Liquid-tight.
• Solvent-free, 100% solids epoxy.
• Abrasion-resistant.
• Easy to apply.
• Easy to maintain and clean.
• Produces a slip-resistant, glossy surface.

FEATURES AND BENEFITS
-
• Good chemical and mechanical resistance.
• Used as a decorative top coat with an orange-peel texture.
• Liquid-tight.
• Solvent-free, 100% solids epoxy.
• Abrasion-resistant.
• Easy to apply.
• Easy to maintain and clean.
• Produces a slip-resistant, glossy surface.
FIELDS OF APPLICATION
-
• Areas subject to normal-to-medium and heavy industrial loads
• Concrete and cement-based substrates
• Warehouses
• Maintenance workshops
• Production areas
• Chemical and pharmaceutical industries
• Shops and supermarkets
• Food industry
• Aircraft hangars
• Car parks
Product Details
~0.5–0.9 kg/m² (Values vary with the roughness of the substrate.)
18.96 kg A metal pail 5.04 kg B metal pail 24 kg A + B kit. Available in a wide range of colours.
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
• Relative humidity: max. 80%
• Application Temperature: min. +10 °C / max. +30 °C; attention must be paid to condensation.
• Substrate temperature: min. +10 °C / max. +30 °C
• Substrate Moisture Content: the moisture content must be max. 4%. (If the moisture content exceeds 4%, ClvSeal EP PRIMER 625 must be used as a moisture-barrier primer.)
For the technical data of this product, please refer to the Technical Data Sheet or contact our Technical Department.
Application
• SURFACE PREPARATION
The concrete substrate must be clean and sound, with sufficient compressive strength (at least 25 N/mm²) and a pull-off strength of at least 1.5 N/mm². The surface must be clean, dry and free from foreign matter such as dirt, oil, coatings and surface curing compounds. Concrete substrates must be prepared using abrasive equipment to remove cement laitance and achieve an open-textured surface. Weak concrete must be removed, and blowholes and voids must be fully opened up. Surface repairs, filling of blowholes and voids, and levelling of the surface must be carried out with suitable products from the CLV Repair and ClvSeal EP Repair product groups. To ensure full anchorage of the coating system to the substrate, anchor grooves must be cut at edges, corners and junctions, and around the edges of drain outlets and drains, etc.
• MIXING
First mix component A thoroughly on its own using mechanical means. Then add component B to component A and mix continuously for approx. 3 minutes until a homogeneous mix is obtained. Depending on the condition of the surface to be coated, add quartz sand filler at 30–50% of the total resin mix. Continue mixing for a further 2 minutes. Transfer the material to another container and mix again. Avoid over-mixing to reduce the formation of air bubbles. Mix with a low-speed (300–400 rpm) electric mixer or other suitable equipment. For mortar preparation, use rotating-pan, trough-type or flat-type mixers. Before starting the application, check and confirm that the substrate moisture, the relative humidity of the environment and the dew point conditions are suitable. If the substrate moisture content is higher than 4%, ClvSeal EP PRIMER primers that act as a moisture barrier can be used. Make sure the substrate is covered with a fully closed, pore-free primer layer. If necessary, a second coat of primer can be applied. Levelling mortar: First, rough surfaces must be levelled. For this purpose, use ClvSeal EP PRIMER products as a mortar (see the Technical Data Sheet for details).
• APPLICATION
ClvFloor 330 TEX is poured onto the substrate and spread with a squeegee. The surface is then rolled in both directions with a texture roller or a short-pile roller to give it its final texture.
If the area needs to be heated, do not use gas, oil, paraffin or other fossil-fuel heaters. Only electric warm-air blowers should be used for heating. Never apply to substrates with rising damp. In addition, protect the freshly applied coating from moisture, condensation and water for at least 24 hours. Thin coatings cannot be applied to dirty or uneven substrates; therefore, both the substrate and the surrounding areas must always be prepared and thoroughly cleaned before application. For colour consistency, ensure that the product applied to each area comes from the same production batch number. Point loads in combination with underfloor heating systems or high ambient temperatures may cause indentations in the resin surface.