ClvFloor TC 105
Two-Component, Water-Based, Polyurethane-Based, Matt, Coloured Top Coat
ClvFloor TC 105 is a water-based, two-component, low-VOC, coloured polyurethane protective top coat for floors.
• UV-resistant, non-yellowing.
• Water-based, low VOC.
• Easy to clean.
• Minimal odour.
• Extends the service life of the top coat.

FEATURES AND BENEFITS
-
• UV-resistant, non-yellowing.
• Water-based, low VOC.
• Easy to clean.
• Minimal odour.
• Extends the service life of the top coat.
FIELDS OF APPLICATION
-
ClvFloor TC 105 is used as a coloured protective top coat in polyurethane product ranges and floor coating systems.
Product Details
0.15–0.20 kg/m²
Comp. A tin: 8.50 kg Comp. B tin: 1.50 kg Kit (A + B): 10.00 kg kit Available in a wide range of colours.
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
| Property | Test Method | Value |
|---|---|---|
| Chemical Base | Clever Lab. | Polyurethane |
| Mixing Ratio | Clever Lab. | 85:15 (A:B, by weight) |
| Consumption | Clever Lab. | 0.15–0.20 kg/m² |
| Appearance / Colour | Clever Lab. | Available in a wide range of colours. |
| Density | Clever Lab. | Component A: 1.05 kg/L Component B: 1.13 kg/L Resin mix: 1.07 kg/L (thin with 5% water.) |
| Product Temperature | Clever Lab. | +10 °C to +30 °C |
| Ambient Temperature | Clever Lab. | +10 °C to +30 °C |
| Working Time | Clever Lab. | +10 °C ~80 min +20 °C ~60 min +30 °C ~30 min |
| Curing Time | Clever Lab. | +10 °C: 24 h – 4 days +20 °C: 12 h – 2 days +30 °C: 8 h – 24 h |
| Time to Traffic | Clever Lab. | +10 °C: 30 h – 48 h +20 °C: 16 h – 24 h +30 °C: 12 h – 18 h |
| Full Cure | Clever Lab. | +10 °C: ~6 days +20 °C: ~4 days +30 °C: ~3 days |
Application
• SURFACE PREPARATION
All dust and loose or unstable particles must be removed from the substrate with a brush and/or vacuum cleaner before applying the product. The substrate must be clean, dry and free from foreign matter such as dirt, oil, grease, coatings and surface curing compounds. The pull-off strength must not be less than 1.5 N/mm². In case of doubt, carry out a trial.
• MIXING
Component A : Component B = 85:15 (by weight) Before starting to mix, homogenise component A mechanically until completely uniform. Then add all of component B and mix continuously for approx. 3 minutes. For a smoother surface, 5–7% water may be added to the mix. To ensure that the mix is completely homogeneous, transfer it to another container and mix again. Avoid over-mixing to prevent air bubbles.
• APPLICATION
Apply ClvFloor TC 105 evenly to the surface with a short-pile roller. Before application, check that the relative humidity and dew point conditions are suitable.
• Protect the freshly applied coating from moisture, condensation and water for at least 7 days (+20 °C).
• Before application, ensure that the substrate is even and clean; thin top coats do not conceal surface irregularities.
• If heating is required, only electric warm-air blowers should be used. Gas, oil, paraffin or other fossil-fuel heaters produce CO2 and H2O vapour, which adversely affects the surface appearance.
• Sanding is recommended on epoxy-based surfaces to ensure adequate adhesion; a green pad can be used for this purpose.