ClvSeal 585
Two-Component, Cement- and Acrylic-Based Waterproofing Coating for Negative- and Positive-Side Applications
ClvSeal 585 is a two-component, cement- and acrylic-polymer-based waterproofing material for concrete substrates, suitable for both negative-side and positive-side applications.
• Resistant to negative and positive water pressure.
(4 bar negative side – 7 bar positive side)
• High durability.
• ClvSeal 585 has capillary action.
• Long working time.
• Does not shrink or crack.
• Vapour-permeable.
• Very high bond strength; works together with the substrate to which it is bonded.
• Easy to prepare and apply.
• Resistant to freeze–thaw cycles.
• Protection of concrete against water and carbonation

FEATURES AND BENEFITS
-
• Resistant to negative and positive water pressure.
(4 bar negative side – 7 bar positive side)
• High durability.
• ClvSeal 585 has capillary action.
• Long working time.
• Does not shrink or crack.
• Vapour-permeable.
• Very high bond strength; works together with the substrate to which it is bonded.
• Easy to prepare and apply.
• Resistant to freeze–thaw cycles.
• Protection of concrete against water and carbonation
FIELDS OF APPLICATION
-
• For vertical and horizontal applications
• Interior and exterior areas
• Bathrooms, wet rooms
• Water tanks
• Tunnels
• Lift shafts
Product Details
Consumption, first coat: 1.30 kg/m² of mix Consumption, second coat: 1.20 kg/m² of mix Consumption, third coat: 1.20 kg/m² of mix
Component A 25 kg kraft paper bag Component B 2 kg metal pail Components A and B 27 kg kit
12 months from the date of production. Storage conditions: store correctly in the original, unopened and undamaged packaging in a dry place between +5 °C and +30 °C.
• Relative humidity: max. 80% • Application temperature: min. +10 °C / max. +30 °C • Beware of condensation. • Substrate temperature: min. +5 °C / max. +25 °C
| PROPERTY | TEST METHOD | VALUE |
|---|---|---|
| Chemical Base | Clever Lab. | Polymer-modified, reinforced special cement and acrylic polymer |
| Appearance / Colour | Clever Lab. | Component A: grey powder |
| Component B: white liquid | ||
| Density | DIN EN ISO 2811-1 | Mixed: 1.98 kg/L |
| Consumption | Clever Lab. | 1st coat: 1.30 kg/m² |
| 2nd coat: 1.20 kg/m² | ||
| 3rd coat: 1.20 kg/m² | ||
| Working Time | Clever Lab. | +25 °C → 35–40 min |
| Resistance to Water under Pressure | EN 12390-8 | 4 bar (negative side) / 7 bar (positive side) |
| Water Vapour Permeability 2 | EN 196-1 | Class I |
| Bond Strength | EN 1542 | >1.5 N/mm² (28 days) |
| Substrate Temperature | Clever Lab. | +5 °C to +25 °C |
| Service Temperature | Clever Lab. | −20 °C to +80 °C |
Application
• SURFACE PREPARATION
Cementitious surfaces of structures in contact with water must be sound, dry, load-bearing, dust-free and clean, and also level. The substrate must be thoroughly cleaned of all oil, grease, rust and paraffin residues that would impair adhesion, and there must be no loose particles on the surface. Any active water leaks and voids in the substrate must be filled with CLV PLUG or CLV REPAIR, and a fillet with a radius of at least 4 cm must be formed at corners and edges. The application surface must be thoroughly wetted and then left until it reaches a damp/dry condition. If the coating material loses its water immediately during application and takes on a matt appearance, this indicates that the substrate has not been sufficiently wetted or is drying too quickly. In such cases, i.e. in hot weather or where the materials are exposed to wind, the mixing water of the material may be increased by 10% for the first coat only.
• MIXING
Pour ClvSeal 585 component B together with the recommended quantity of mixing water into a clean mixing bucket, then gradually add powder component A and mix with a mixer at 400–600 rpm for 3–5 minutes until a homogeneous, lump-free mix is obtained. Allow to stand for approx. 3–5 minutes and mix again for 30 seconds; the material is then ready for use.
| ClvSeal 585 | Comp. A | Comp. B | Mixing water |
|---|---|---|---|
| Mix Quantity | 25 kg | 2 kg | 5.00–5.50 L |
| Mixed density | 1.98 kg/L | ||
Apply the prepared ClvSeal 585 mix in two or three coats using a waterproofing brush. The brush direction of each coat must be perpendicular to that of the previous coat. The waiting time between coats depends on ambient conditions. ClvSeal 585 must be used for embedding the mesh at corners. Apply the first coat with a waterproofing brush. Once it has dried, lay the waterproofing mesh and apply the second and third coats over it.
• When applying ClvSeal 585, if the ambient and substrate temperatures are below +5 °C or above +25 °C, wait for suitable temperatures. In addition, do not apply in extremely hot or rainy weather.
• ClvSeal 585 applied at +23 °C gains mechanical strength after 2 days, becomes watertight after 7 days and reaches its final strength after 14 days. The surface must be protected from sun, wind, rain or frost for the first 24 hours.
• At low temperatures the reaction slows down, which extends the pot life and working time. High temperatures accelerate the reaction, and the times given above are shortened accordingly. To allow the material to cure fully, the ambient and substrate temperatures must not fall below the minimum permitted temperature.
• The wet film thickness must not exceed 1.30 mm per coat. • Areas subject to foot traffic must be covered with screed.