ClvSeal EP PRIMER 617
Two-Component, Solvent-Free Epoxy Primer
ClvSeal EP PRIMER 617 is a two-component, epoxy-based, low-viscosity, solvent-free epoxy primer.
• Solvent-free.
• Easy to apply.
• Excellent adhesion to all types of substrates.
• Seals capillary voids and pores beneath waterproofing systems, preventing the formation of pinhole bubbles.
• Low viscosity.
• Low emission.

FEATURES AND BENEFITS
-
• Solvent-free. • Easy to apply. • Excellent adhesion to all types of substrate. • Seals capillary voids and pores beneath waterproofing systems, preventing the formation of pinhole bubbles. • Low viscosity
FIELDS OF APPLICATION
-
• Used on concrete and cementitious mineral substrates.
• Suitable for interior and exterior application.
• Can be mixed with dry silica sand in a ratio of 1:2 to form a primer layer.
• Suitable for mortar floor coatings.
Product Details
Total consumption: 0.25–0.5 kg/m² Consumption will vary when used as a repair mortar or filler.
Component A: 14.47 kg metal pail Component B: 6.50 kg metal pail A and B kit: 20.97 kg
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
• Concrete strength class: C20/25 • Substrate moisture content: W<5% • Temperature: +5 °C to +35 °C • Relative humidity: <85% For further information, please consult our Technical Department.
| PROPERTY | TEST METHOD | VALUE | ||
|---|---|---|---|---|
| Product Type | Clever Lab. | Epoxy | ||
| Mixed density | ASTM D 1475 / EN ISO 2811-1 | 1.07 g/cm³ (+20 °C) | ||
| Mixing Ratio | Clever Lab. | A:B = 100:43 (by weight) | ||
| Viscosity | ASTM D4287 / EN ISO 3219 | 490 cP (+20 °C) | ||
| Application Temperature | Clever Lab. | +5 °C to +30 °C | ||
| Pot Life | Clever Lab. | Temperature | Time | |
| +10 °C | ~60 min | |||
| +23 °C | ~30 min | |||
| +30 °C | ~15 min | |||
| Compressive Strength (28 days) | Clever Lab. | 81 N/mm² | ||
| Curing Time | Clever Lab. | Overcoating – with Solvent-Free Products over ClvSeal EP PRIMER 617 | ||
| Temperature | Time | |||
| +10 °C +20 °C +30 °C | min. 24 h / max. 48 h min. 7 h / max. 36 h min. 3 h / max. 24 h | |||
| Full Cure | Clever Lab. | Temperature | Time | |
| +10 °C | 5 days | |||
| +20 °C | 3 days | |||
| +30 °C | 2 days | |||
| * Viscosity measured at +25 °C in accordance with EN ISO 3219. Viscosity decreases as temperature rises. | ||||
Application
• SURFACE PREPARATION
Before application, all factors that would impair adhesion and bonding, such as oil, grease, paraffin residues and release agents, must be removed from the surface. After washing with high-pressure water, the surface must be dried thoroughly. Surface defects must be repaired with suitable products; alternatively, it is recommended to use ClvSeal EP PRIMER 617 as a repair mortar by adding silica sand in a ratio of (1:0.5), (1:2). The concrete substrate must have a strength of min. 1.5 N/mm² and must be at least 3 weeks old. In addition, concrete substrates must be mechanically ground, then washed with water jets and dried. Substrate moisture must not exceed 5%.
• APPLICATION
Before use, open the containers and mix each component separately for 2–3 minutes with a low-speed mixer. After Component A has been mixed on its own, add it to Component B and mix again. Allow the mix to stand for 1 min, then mix again for 2–3 min without entraining air. The mix must be used within 15–20 minutes with a roller, squeegee or brush. The curing time is 7–8 hours. Once the mix has been prepared, silica sand can be added in a ratio of between (1:05), (1:1) and (1:2) before application. If a floor coating or polyurea is to be applied, broadcast 0.1–0.3 mm silica sand at a consumption of approx. 1.0 kg/m² onto the freshly applied ClvSeal EP PRIMER 617 while it is still wet.
• Substrate temperature must be between +8 °C and +35 °C.
• Not recommended for unsound substrates.
• Do not mix by hand.
• Do not thin.
• Before application, make sure that the containers have been kept at min. 25 °C so that they have reached 20 °C.