ClvSeal EP PRIMER WB
Two-Component, Water-Based Epoxy Primer
ClvSeal EP PRIMER WB is a two-component, chemically curing, moisture-tolerant, water-based epoxy primer.
• Water-based.
• Acts as a highly effective barrier against water and moisture.
• Provides high adhesion to all absorbent substrates, including damp concrete.
• Resistant to general cleaning agents and chemicals.
• Odourless.
• Non-flammable.
• Suitable for application in enclosed areas.
• Easy application.
• Strong adhesion

FEATURES AND BENEFITS
-
• Water-based.
• Acts as a highly effective barrier against water and moisture.
• Provides high adhesion to all absorbent substrates, including damp concrete.
• Resistant to general cleaning agents and chemicals.
• Odourless.
• Non-flammable.
• Suitable for application in enclosed areas.
• Easy application.
• Strong adhesion
FIELDS OF APPLICATION
-
• Interior and exterior areas
• Primer for epoxy, PU or cementitious systems
• In moisture barrier applications
• Concrete sealing
Product Details
Consumption (minimum): 0.15–0.30 kg/m² As a moisture barrier: 0.50–0.60 kg/m²
Component A: 5 kg Component B: 15 kg Kit in plastic pails A+B kit: 20 kg Transparent
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
• Concrete strength class: C20/25 • Substrate moisture content: W<5% • Temperature: +5 °C to +35 °C • Relative humidity: <85% For further information, please consult our Technical Department.
| PROPERTY | TEST METHOD | VALUE |
|---|---|---|
| Product Type | Clever Lab. | Two-component water-based epoxy |
| Density | ASTM D 1475 / EN ISO 2811-1 (+20 °C) | 1.05 g/cm³ (±0.05) |
| Viscosity | ASTM D 2196-86 / EN ISO 3219 (+25 °C) | 100–300 cP |
| Application Temperature | Clever Lab. | +5 °C to +35 °C |
| Thinning | Clever Lab. | 20–30% with water |
| Water Vapour Permeability | EN ISO 7783-2 | 3.9 g/m² 24 h Class III (low, <15) |
| Liquid Water Permeability | NF EN 1062-3 | 0.003–0.006 kg/(m²·h⁰·⁵) Class III (low, < 0.1) |
| Compressive Strength | Clever Lab. | > 3 N/mm² |
| Adhesion to Concrete | ASTM D 4541 (+23 °C) | > 3 N/mm² |
| Pot Life | Clever Lab. (+25 °C) | 1 h |
| Initial Drying Time | 25 °C / 55% RH | 4–5 h |
| Overcoating Time | Clever Lab. | 6–12 h |
| Abrasion Resistance | ASTM D4541 (TABER 503) | 120*10 |
| * Viscosity measured at +25 °C in accordance with EN ISO 3219. Viscosity decreases as temperature rises. | ||
Application
• SURFACE PREPARATION
Before application, all factors that would impair adhesion and bonding, such as oil, grease, paraffin residues, cement laitance, loose particles, release agents and old cured membranes, must be removed from the entire surface. Surface defects must be repaired with suitable products. After surface preparation, the tensile strength of the concrete substrate must be at least 1.5 N/mm².
• APPLICATION
Combine Components A and B and mix for 2–3 minutes with a low-speed mixer. Once mixing is complete, thin with 20–30% water to make the product ready for use. The pot life of the mix is 60 minutes at +25 °C. Higher temperatures reduce the pot life. Do not leave the mix for more than 60 minutes before applying it. Once surface repair and preparation are complete, apply to the substrate by roller in accordance with the selected system. Good ventilation will prevent condensation and ensure optimum coating performance. Ventilation must also be maintained during curing. Once the white film on the primed surface has turned transparent, proceed with the application of the epoxy or polyurethane top layer. Consumption as a primer is 0.15–0.20 kg/m². As a moisture barrier, a minimum of 3 coats must be applied to give 0.50–0.60 kg/m².
Not recommended for unsound substrates.
Not suitable for waterproofing swimming pools containing chemically treated water.