ClvSeal PU 35
Single-Component, Polyurethane-Based Sealant
ClvSeal PU 35 is a single-component, high-modulus, moisture-curing polyurethane joint sealant.
- • Excellent adhesion to all types of substrates, primed or unprimed.
- • Easy to apply and tool.
- • High chemical resistance.
- • Suitable for sealing joint systems in water tanks and swimming pools with chemically treated water.
- • Can be overpainted.
- • Non-sagging, thixotropic.
- • Watertight once dry.
- • Movement capability of 25%.
- • No air bubbles form during curing.

FEATURES AND BENEFITS
-
• Excellent adhesion to all types of substrates, primed or unprimed.
• Easy to apply and tool.
• High chemical resistance.
• Suitable for sealing joint systems in water tanks and swimming pools with chemically treated water.
• Can be overpainted.
• Non-sagging, thixotropic.
• Watertight once dry.
• Movement capability of 25%.
• No air bubbles form during curing.
FIELDS OF APPLICATION
-
• Joint sealing
• Expansion joints in concrete slabs
• Water tanks and swimming pools
• Joints in irrigation channels
• Expansion joints in roofs and terraces
• Horizontal and vertical expansion joints
Product Details
| Joint Width | Joint Depth | Joint Length (m/600 ml pack) |
| 10 mm | 5 mm | 6 |
| 20 mm | 10 mm | 3 |
| 30 mm | 15 mm | 1.3 |
White and grey; supplied in 600 ml aluminium foil packs.
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
| PROPERTY | TEST METHOD | VALUE |
|---|---|---|
| Product Type | Clever Lab. | Single-component polyurethane sealant |
| Consistency | Clever Lab. | Thixotropic paste |
| Density | ASTM D1475 / EN ISO 2811-1 (+20 °C) | 1.15 ± 0.05 g/cm³ |
| Curing Rate | Clever Lab. | 2 mm/day |
| Modulus at 100% Elongation | ASTM D-412 | 0.35–0.40 N/mm² |
| Movement Capability | Clever Lab. | 25% |
| Elastic Recovery | Clever Lab. | > 60% |
| Hardness | ASTM D2240 / DIN 53505 / EN ISO 868 | 40 (±5) Shore A |
| Elongation at Break | ASTM D412 (+23 °C) | > 600% |
| Adhesion to Concrete | EN 1542 (+23 °C) | > 1.5 N/mm² |
| Initial Drying Time | 25 °C / 55% RH | 60–90 min |
| Drying Time | Clever Lab. | 2 mm / 24 h |
* Viscosity measured at +25 °C in accordance with EN ISO 3219. Viscosity decreases as temperature rises.
Application
• SURFACE PREPARATION
The joint must be cleaned before application. Make sure that the joint is dry. The substrate within the joint must be completely free from anything that would prevent or impair adhesion and bonding, such as oil, grease, fuel, paraffin and silicone. If the base of the joint is open, a polyethylene backer rod must be used, and the application area must be formed by leaving a depth equal to half the joint width (width 2 / depth 1).
• PRIMING
A suitable primer must be selected according to the condition of the substrate and the climatic conditions. PU PRIMER 200 is recommended as a primer on porous substrates, and ClvSeal EP PRIMER WB on damp substrates.
• APPLICATION
Insert the backer rod into the joint so as to prevent air from entering the joint. Cut the sealant pack at the very tip and place it in the gun. Cut the nozzle to obtain a suitable and correct flow rate and fit it to the gun. Apply the sealant so that no air can enter the joint. In wide joints, several passes with the gun are required to ensure full contact of the sealant with the sides and base. The sealant must be tooled immediately after application
• Not recommended for unsound substrates.
• Not suitable for waterproofing swimming pools containing chemically treated water.