COLD POLYUREA
2-Component, Cold-Applied, Fast-Curing Polyurea Liquid Waterproofing Membrane
COLD POLYUREA is a two-component, fast-curing, cold-applied, liquid-applied polyurea waterproofing material.
• Easy to apply (by brush, roller or spray).
• Does not require expensive application equipment and machinery.
• Forms a seamless, monolithic film that leaves no possibility of joints or leaks when applied.
• Provides an elastomeric and hydrophobic layer.
• Effectively permeable to water vapour. Owing to its breathable structure, it does not cause moisture to accumulate beneath the layer.
• Even if COLD POLYUREA is damaged in some way, the damaged area can be repaired quickly and easily.
• Effective resistance to chemicals.
• Cures quickly in all weather conditions.
• Heat resistance performance between −40 °C and +90 °C.

FEATURES AND BENEFITS
-
• Easy to apply (by brush, roller or spray).
• Does not require expensive application equipment and machinery.
• Forms a seamless, monolithic film that leaves no possibility of joints or leaks when applied.
• Provides an elastomeric and hydrophobic layer.
• Effectively permeable to water vapour. Owing to its breathable structure, it does not cause moisture to accumulate beneath the layer.
• Even if COLD POLYUREA is damaged in some way, the damaged area can be repaired quickly and easily.
• Effective resistance to chemicals.
• Cures quickly in all weather conditions.
• Heat resistance performance between −40 °C and +90 °C.
FIELDS OF APPLICATION
-
• Terraces and balconies
• Bridges and tunnels
• Wet rooms
• Floors
• Areas beneath tiles
• Reinforced concrete structures
Product Details
Consumption for single-coat application (minimum): 1.50–2.00 kg/m².
Red (RAL3013), in 25 kg (Component A) + 1.5 kg (Component B) metal pails.
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
• Concrete strength class: C20/25 • Substrate moisture content: W <5% • Temperature: +5 °C to +35 °C • Relative humidity: <85%
| Property | Test Method | Value |
|---|---|---|
| Product Type | Clever Lab. | Cold-applied polyurea |
| Density | ASTM D1475 / EN ISO 2811-1 (+20 °C) | 1.30 ± 0.05 g/cm³ |
| Viscosity | ASTM D2196-86 / EN ISO 3219 (+25 °C) | 3,000–5,000 cP |
| Water Vapour Permeability | EN ISO 7783 | 0.8 g/(m²·h) |
| Gloss | Clever Lab. | Semi-gloss |
| Application Temperature | Clever Lab. | +5 °C to +35 °C |
| Solids Content | Clever Lab. | 90% (±5) |
| Resistance to Heat Ageing | Clever Lab. | 100 days at +80 °C |
| Heat Shock Resistance | Clever Lab. | 200 °C – Pass |
| Hardness | ASTM D2240 / DIN 53505 / EN ISO 868 | 50 Shore A |
| Elongation at Break | ASTM D412 (+23 °C) | >500% |
| Pot Life | Clever Lab. (+25 °C) | 20–30 min |
| Tensile Strength at Break | ASTM D412 (+23 °C) | >10 N/mm² |
| Adhesion to Concrete | EN 1542 (+23 °C) | >2 N/mm² |
| Service Temperature | Clever Lab. | −40 °C to +90 °C |
| Initial Drying Time | 25 °C / 55% RH | 2–3 h |
| Waiting Time between Coats | Clever Lab. | 3–6 h |
Note: Viscosity measured at +25 °C in accordance with EN ISO 3219. Viscosity decreases as temperature rises.
Application
• SURFACE PREPARATION
Before application, all contaminants that impair bonding and adhesion, such as oil, grease, paraffin residues, cement laitance, loose particles, release agents and old cured membranes, must be removed from the substrate. After cleaning with high-pressure water, the substrate must be dried. Surface defects must be repaired with suitable products.
• PRIMING
For absorbent substrates such as concrete, cement or screed, use PU PRIMER 200 or ClvSeal EP PRIMER 617. On damp substrates, ClvSeal EP PRIMER 625 should be preferred. On non-absorbent substrates such as metal and ceramics, use PRIMER T. For detailed information, refer to the primer table.
• COLD POLYUREA must be covered after application.
• Not recommended for unsound substrates.
• Not suitable for waterproofing swimming pools containing chemically treated water.
• Forms an elastic, durable film on the substrates to which it is applied. For use in areas exposed to the open air and external influences, PU 650 TC-1K must be used as the top coat.