PU SMART FLEX
1-Component PU/Polyurea-Based Liquid Waterproofing with High Chemical Resistance
PU SMART FLEX is a single-component, cold-applied, polyurethane/polyurea-based liquid-applied membrane developed especially for waterproofing bridge decks and for areas requiring high abrasion resistance.
• High crack-bridging ability.
• Easy to apply (by brush, roller or airless spray).
• Good compatibility with asphalt surfacing without the need for an additional bonding layer.
• High heat resistance.
• High chemical resistance.
• Resistant to substances such as machine oil, petrol and gas.
• Provides excellent elasticity and crack bridging at low and high temperatures.
![]()
FEATURES AND BENEFITS
-
• High crack-bridging ability.
• Easy to apply (by brush, roller or airless spray).
• Good compatibility with asphalt surfacing without the need for an additional bonding layer.
• High heat resistance.
• High chemical resistance.
• Resistant to substances such as machine oil, petrol and gas.
• Provides excellent elasticity and crack bridging at low and high temperatures.
FIELDS OF APPLICATION
-
• Bridge decks (asphalt-surfaced bridges)
• Floors
• Underground applications such as tunnels and car park decks
• Terraces, verandas and balconies
• Top coat application in areas exposed to high abrasion and heavy traffic
Product Details
• Spraying (per coat): 0.75–0.90 kg/m²
• Total consumption (minimum): 1.50–1.80 kg/m²
• For bridge applications (minimum): 2.50 kg/m²
In 25 kg metal pail, Grey
Store the product in its unopened original packaging at temperatures between +5 °C and +25 °C for a maximum of 12 months. Once opened, use the product as soon as possible.
| PROPERTY | TEST METHOD | VALUE |
|---|---|---|
| Product Type | Clever Lab. | 1-comp. PU/polyurea |
| Density | ASTM D 1475 / DIN 53217 / ISO 2811-1 (+20 °C) | 1.45 (±0.05) g/cm³ |
| Viscosity | ASTM D 4287 / EN ISO 3219 (+25 °C) | 2000–5000 cP |
| Water Vapour Permeability | ASTM E96 | 0.8 g/(m²·h) |
| Gloss | Clever Lab. | Semi-gloss |
| Application Temperature | Clever Lab. | +5 °C to +35 °C |
| Resistance to Heat Ageing | EOTA TR011 | 100 days at 80 °C – Pass |
| Heat Shock Resistance | Clever Lab. | 220 °C – Pass |
| Solids Content | Clever Lab. | 85% (±5) |
| Hardness | ASTM D2240 | > 80 (Shore A) |
| Elongation at Break | ASTM D 412 (+23 °C) | > 350% |
| Tensile Strength at Break | ASTM D 412 (+23 °C) | > 7 N/mm² |
| Adhesion to Concrete | EN 1542 (+23 °C) | > 2 N/mm² |
| QUV | ASTM G154 | 2000 h – Pass |
| Abrasion Resistance (Taber) | ASTM D4060-14 | 30 mg loss (CS17/1000/1000) |
| Service Temperature | Clever Lab. | −40 °C to +80 °C |
| Initial Drying Time | 25 °C / 55% RH | 6 h |
| Waiting Time between Coats | Clever Lab. | 6–24 h |
Application
• SURFACE PREPARATION
Before application, all contaminants that impair bonding and adhesion, such as oil, grease, paraffin residues, cement laitance, loose particles, release agents and old cured membranes, must be removed from the substrate. After cleaning with high-pressure water, the substrate must be dried thoroughly. Surface defects must be repaired with suitable products.
• PRIMING
For absorbent substrates such as concrete, cement or screed, use PU PRIMER 200 or ClvSeal EP PRIMER 617. On damp substrates, ClvSeal EP PRIMER 625 should be preferred. On non-absorbent substrates such as metal and ceramics, use PRIMER T. For detailed information, refer to the primer table.
• APPLICATION
Before use, open the container and mix for 2–3 minutes with a low-speed mixer. If required, add a maximum of 5–7% CLEVER 001 for spray application. Apply to the previously primed surface with a roller, squeegee or brush until the entire surface is covered. For detailed information, refer to the primer table.
• Not recommended for unsound substrates.
• Not suitable for waterproofing swimming pools containing chemically treated water.